+++ /dev/null
-Linux Infrared Remote Control - use an easy to build home-brewn IR-receiver, an
-(almost) arbitrary remote control and control your Linux box with it! More
-about it at www.lirc.org. Be sure to read LIRC documentation before going ahead
-in this README.
-
-If you have installed the lirc-package, configure will autodetect it. If LIRC
-support is enabled and an error occurs Geeqie will tell you on startup. The
-application name for Geeqie is geeqie. Here is the list of supported commands:
-
-DOWN [int] - Move "camera" down by the specified amount. Default=1
-EXIT - Exit Geeqie
-FIRST - Jump to first image
-INFO - Show image information (full screen only)
-LAST - Jump to last image
-LEFT [int] - Move "camera" left by the specified amount. Default=1
-NEXT - Go to next image
-PAUSE - Pause/unpause slideshow
-PREV - Go to previous image
-RIGHT [int] - Move "camera" right by the specified amount. Default=1
-ROTATE_90 - Rotate image 90 degrees clockwise.
-ROTATE_90_CC - Rotate image 90 degrees counter-clockwise.
-SET_INV_ZOOM [int] - Zoom to 1/Nx. Deafult=1x
-SET_ZOOM [int] - Zoom to Nx. Default=1x
-UP [int] - Move "camera" up by the specified amount. Default=1
-ZOOM_IN [int] - Zoom in. Value specifies the amount of zoom.
-ZOOM_MAX - Zoom to fit image
-ZOOM_OUT [int] - Zoom out. Value specifies the amount of zoom.
-
-Don't forget to enable the repeat flag in .lircrc when it make sense
-(directional buttons, zoom in and out, ...)
-Here's an excerpt from my .lircrc:
-
-begin geeqie
- begin
- prog = geeqie
- button = vol_up
- config = ZOOM_IN 1
- repeat = 3
- end
- begin
- prog = geeqie
- button = vol_down
- config = ZOOM_OUT 1
- repeat = 3
- end
- begin
- prog = geeqie
- button = down
- config = DOWN 10
- repeat = 1
- end
- begin
- prog = geeqie
- button = up
- config = UP 10
- repeat = 1
- end
- begin
- prog = geeqie
- button = right
- config = RIGHT 10
- repeat = 1
- end
- begin
- prog = geeqie
- button = left
- config = LEFT 10
- repeat = 1
- end
- begin
- prog = geeqie
- button = back
- config = PREV
- end
- begin
- prog = geeqie
- button = forw
- config = NEXT
- end
- begin
- prog = geeqie
- button = skip_back
- config = FIRST
- end
- begin
- prog = geeqie
- button = skip_forw
- config = LAST
- end
- begin
- prog = geeqie
- button = pause
- config = PAUSE
- end
- begin
- prog = geeqie
- button = surround
- config = SET_ZOOM
- end
- begin
- prog = geeqie
- button = 1
- config = ROTATE_90
- end
- begin
- prog = geeqie
- button = 2
- config = ROTATE_90_CC
- end
- begin
- prog = geeqie
- button = 3
- config = INFO
- end
- begin
- prog = geeqie
- button = 4
- config = EXIT
- end
-end geeqie
-
-At the moment Geeqie uses the standard location for the lirc-config file
-(~/.lircrc).
-
-LIRC support and documentation by Matteo Beniamino
-<beniamino@tautologica.org>.
-
-(This file is 'inspired' by LIRC documentation from mplayer).